← Corbin
Notes: Required Holes Required Holes Function B C D Function B C D Backset is measured from centerline of bevel which is ML2002 Χ Χ ML2056 centerpoint of door thickness. Non-beveled door shown. ML2057 Χ Χ ML2003 (*) When preparing doors for lead wrapped locks, add 1/8 (6) ML2004 X X ML2058 Χ Χ (3.2) to dimensions marked (*) to allow proper clearance. Χ ML2010 Χ ML2059 Χ 1-1/8 (28.6) strike lip suits frame for 1-3/4 (44.5) thick Х ML2020 Χ ML2060 door, lip will vary for other door thicknesses. ML2022 Χ ML2062 Χ Χ For open back strike, refer to template T30606. 4. ML2024 Χ Χ ML2065 Χ 5. Dimensions given in inches and (mm). ML2029 Х Χ Χ Χ Χ ML2067 ML2030 Χ Χ Χ Χ ML2068 ML2032 Χ ML2069 X X Х ML2042 Χ Χ ML2072 Χ Х ML2048 X ML2073 Χ ML2049 Χ Χ Χ ML2075 X Χ ML2051 Χ Χ ML2080 T ML2052 Χ ML2082 X Χ CAUTION: DOOR & FRAME MANUFACTURERS ML2053 Χ Χ Χ ML2087 Χ Χ When door gasketing or silencers are used, proper allowances must be made for strike location to maintain a common Х ML2054 Х Χ Χ ML2090 ML2055 Χ ML2092 centerline with lock and door as shown so that bolt will freely T = CUT HOLE ON TRIM SIDE OF DOOR ONLY Plaster Guard by Frame Manufacturer Cylinder (31.8) 1" Min. A 1-5/16 (33.3) Dia. – Outside Only Min. (2.4)(25.4) B 1-5/16 (33.3) Dia. Thru Turnpiece – Inside Emergency Key/Indicator - Outside Metal Door Prep Wood Door Prep C 5/8 (15.9) Dia. – Inside Only (See Note 3) D |5/8 (15.9) Dia. Thru Frame (28.6)#12-24 TAP .173 Dia. Strike/Lock/Door #12-24 Tap for 1.25 (31.8) Pilot Hole Combination Screw Min. Depth (2 Places) (2 Places) (114.3)+031(2 Places) 1.250 -.000 (31.8)<u>5/</u>8 (31.8)Ø1.125 -.000 (15.9) 3<u>/</u>4 Max. 1-3/16 (28.6)(30.2) (104.8)(19.1)+.031 R.125 (3.2) Max -.000 (4 Places) ₹ Cylinder <u>2-7/16</u> 6-5/8 + 031 +015 (61.9)-.000 (168)-.000 4-7/8 3-1/2 5.625 3-3/8-.000 3-5/8 G Strike (203.2)(142.9)(123.8) (88.9)(85.7) 1.000 -.000 (92.1)£ Lock Min. 3/8 (25.4)(28.6)7-1/4 (9.5)(184.2)€----Knob/ 1-1/2 (184.2) +031 Lever (38.1)(17.5)<u>1/2</u> Min. +.031 (12.7)3/8 1.250 -.000 ±.008 (30.2)(31.8)(95.3)(5.6)(64.3 2.750 ±.031 (69.9) Tolerances Template Cross Reference Inches (mm) Half Trim ML T31184 (.127) .005 T31186 Full Dummy Trim .010 Half Dummy Trim T31187 (.381) .015 RESPONSIBILITY
DOOR AND FRAME MANUFACTURERS ARE RESPONSIBLE FOR PROVIDING ADEQUATE CONSTRUCTION OR REINFORCEMENTS FOR PROPER INSTALLATION OF HARDWARE SHOWN. ALL ARCHITECTURAL BUILDERS HARDWARE MUST BE INSTALLED ON PROPERLY REINFORCED DOORS AND FRAMES, REGARDLESS OF TYPE,
MATERIAL, OR METHOD OF CONSTRUCTION.
ML200 Series Inspire™ Roseless Trim
ASSA ABLOY
www.corbinrusswin.com
SUPERSEDES T31183-5 DO NOT SCALE DRAWING 03/23 T31183-6 1 of