M9200 Mortise Lock Bodies (all functions)

REVISIONS DESCRIPTION APPROVED ZONE DATE REVISED PER EN727322 1. HOLE POSITION 3 WAS [1-1/4] 2. HOLE POSITION 4 WAS [1-1/4] A8, H6 1/13/2022 TWF 3. NOTE 1 (MATERIAL COMPLIANCE) ADDED TO DRAWING FORMAT. 5 THIS TEMPLATE COVERS THE M9200 SERIES LOCKSET IN ACCORDANCE WITH REQUIRED HOLES THE SPECIFICATIONS INDICATED BELOW: 3 1.125" 1.125" 2.125" 2.125" [1-1/8"] [2-1/8"] [2-1/8"] DIA. DIA. DIA. .500" [1/2"] DIA. .500" [1/2"] DIA. .250" [1/4"] DIA. FUNCTION VARIABLE DIMENSIONS [1/4"] DIA. LOCK LINES & VARIATIONS 03, 21 DIM "A" DIM "B" [7/32"] M9200 1.250 ± .015 [1-1/4"] .906 [29/32"] 04, 37, 55 .219 06 05*, 24, 25, 43, 45 16, 17, 26, 38, 39, 40 4 OF BEVEL DIM "A" SECTION A-A $^\backslash ast$ ALL 05 LOCKS MANUFACTURED PRIOR TO 7/6/04 USE 55 FUNCTION DOOR PREP. [2-3/4"] Q OF DOOR-2X 2.750 Q OF BEVEL— BACKSET Q OF BEVEL MOUNTING SCREWS 2X DRILL AND TAP FOR #12-24 x .750 [3/4"] SCREW 8-1/32" Q OF STRIKE-8.031 8.000 [2-15/32"] [7-1/4"] [3/8"] [5-1/2"] 2X 2.469 7.250 .375 2X 5.500 [1-51/64"] [3-5/8"] 2X 1.797 Q OF LOCKBODY-3.625 [6-1/2"] 6.500 4.000 Q OF LEVER [5/8"] OR KNOB 4X .625 OUTSIDE OF DOOR INSIDE OF DOOR DIM "B" [27/64"] 4X .422 DETAIL OF SUGGESTED DOOR-CUT SARGENT Manufacturing Company 1. ■ DENOTES HOLE REQUIRED FOR FUNCTION LISTED. (CHECK TABLE BEFORE CUTTING HOLE.) ASSA ABLOY 100 Sargent Drive New Haven, CT 06511 2. REFER TO TRIM TEMPLATE FOR ADDITIONAL HOLE REQUIREMENTS. TEMPLATE: MORTISE LOCK FOR M9200 SERIES 3. SUITABLE REINFORCEMENTS REQUIRED FOR METAL DOORS. 09-SEPT-11 4. FOR DETAILS, SEE STRIKE TEMPLATE 7063. (LOCKBODIES ONLY) METAL DOORS ONLÝ 5. FOR ADDITIONAL DETAIL FOR SOLENOID OPERATED FUNCTIONS (70,71,72, & 73), SEE TEMPLATE 7065 5 4483 NOTICE TO PERSONS RECEIVING THIS DRAWING AND/OR UNLESS OTHERWISE DRAWING COMPLIES DRAWING COMPLIES MATERIAL WITH ASME Y14.5M - 1994 Oak TEMPLATE: MORTISE LOCK TECHNICAL INFORMATION M9200 MORTISE LOCK The material disclosed herein is the confidential and INCH proprietary information of Sargent Manufacturing Company (the "Company"). This drawing and/or technical information is issued in MM ANGLES ± 0°30' FRACTIONS ± 1/64 SURFACE FINISH 63 NOTES: DATE CREATED 04/26/2018 DRAWN BY DESIGNED BY STEVE GABRY HEAT TREATMENT confidence for engineering information only and may not be reproduced or used to manufacture anything, including THIRD ANGLE PROJECTION 1. MATERIAL AND MANUFACTURING PROCESS MUST COMPLY the items shown or referred to hereon, without direct written permission from the Company. This drawing and/or technical information is the property of the Company and ASSA ABLOY IRFACE/FINISH SCALE 1:2 DOCUMENT ID D000919130-000 WITH ASSA ABLOY AMERICAS, PRODUCT COMPLIANCE is loaned for mutual assistance to be returned when its SPECIFICATION DOCUMENT D001117360. SURFACE AREA 312.644000 i NUMBER (ALT ID) 4483 REV 5 purpose has been served or upon the request of the 0.423000 lb | VOLUME | 20.929000 Company. SHEET 1 OF 1 CONFIGURATION All Approved 2022-01-25 4 LEGACY ID

В