Installation Instructions for 597, 598, 599 Series Holders & Stops

Open the original PDF document

View PDF

INSTALLATION INSTRUCTIONS FOR SARGENT® SURFACE 597, 598, 599 SERIES OVERHEAD HOLDERS & STOPS

SARGENT ASSA ABLOY

NON-HANDED. LEFT HAND SHOWN, RIGHT HAND OPPOSITE.

  • 1 Use the attached template that corresponds with the same type of hinge being used.
    • Drill door to attach channel, drill and tap frame for 1/4-20 machine screws to attach jamb bracket.
  • 2 Secure channel using machine screws and mortise nuts (spring end towards hinge).
    • Secure jamb bracket to frame with fasteners provided.

3 Install latch and control knob for Hold Open models (597H, 598H, 599H).

  • · Place latch into channel.
  • Insert control knob thru holes in door, channel and into latch.
  • Install set screw into latch and secure to control knob.
  • · Check operation.

  • 4 Holding Tension adjustment is easily made with a 1/8" Allen wrench.
    • To increase tension insert wrench as shown and turn clockwise 1/4 turn for desired tension.
    • To activate hold open feature rotate control knob with door slightly open.
    • · Check operation.

ASSA ABLOY

Г Г Т 1
UP 2 = " 1층 - 2축 13 - 2 13 13 2 ACCC (
590 MOUNTING GROUP 2 OI OI 3E I 4 2 യ്യവ Σ|4 ½ ½ 5
32 8 		nla 1 1
10M 065 HINGE TYPE BUTT HINGE 1 0 SWING CLEAR
HINGE 		OFFSET - ,
၁ 1 17 7 6 21
0.0 В 1 3 2 7 =
STOP) 110 ٧ = 5
13 		† -10 7 7 7 8
FOR 3 5° В 1 ري
ماري 		+ 7 3 ω 118
NOTE 2 105 V 1 9 - 10 7 6 - | 4
I (SEE .00 В 1 -|o 0 7 5 Σ 118
D OPEN 10 V 1 6
6 		• 1-10 o 8 2
DEGREE OF OPENING AT HOLD OPEN (SEE NOTE 2 FOR STOP) 9.5 В 1 4
ام 		, œ 12
95. A 1 9 , 7 3 ω 8 2
.06 В 1 4
دام 		• 8
0 		٥ 12 5
6 V : 7 7 3 4 9 3
8
85° В 2 8 7 8 13 1 8
3 Y 7 1 - 1 8
0 | 0 		0 10\frac{1}{4} 13\frac{1}{8}
ACTUAL
DOOR WIDTH 		24^{-32}\frac{1}{2} 0 39 1 AND OVER
MODEL
NO. 		5975 598H 5985 599H
&
599S 		4

m L 1/4 13/16 1. DIMENSIONS ARE GIVEN FOR THE HOLD OPEN POSITION. DEAD STOP OCCURS 5-9* AFTER HOLD OPEN. *A* & *B* DIMENSIONS ARE GIVEN FROM C OF HINGE.

FOR DEAD STOP TEMPLATING, ADD 1/2 TO DIM. "A" AND 3/8 TO DIM. "B".

NOTES

SUFACE MOUNTED CHANNEL -

THRU-BOLT

FOR GROMMET NUT DRILL \phi \frac{7}{16} HOLE

- 12 GA. MIN. REINFORCEMENT FOR METAL DOORS

- DOOR

SWING CLEAR HINGE

1 5/16

3 13/16 HOLE FOR 5/16-18 x 2 -3/16

SARGENT Manufacturing Company 100 Sargent Drive New Haven, CT 06511 DATA SHEET: 597-599 SERIES DOOR HOLDERS AND STOPS - MOUNTING GROUP 2

JAMB BRACKET DETAIL

3/16

A7480 B FFECTIVE DATE APRIL 02

FOR CONTINUOUS HINGES USE SIMILAR BUTT HINGE VALUES,

FOR DOORS UNDER 25° WIDE, THE STOP MAY HAVE TO BE MODIFIED TO ALLOW FOR CHANNEL CLEARANCE.

THRU BOLTS AND GROMMET NUTS PROVIDED ALLOWS CHANNEL TO BE MOUNTED ON 1 3/4 - 2 DOORS.

5. θ.

4. LEFT HAND SHOWN, RIGHT HAND OPPOSITE.

3.

Copyright © 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.

{ Т \overline{} \overline{} Т
1 1 d DOOR - 1 \frac{14}{2} - \frac{2}{2} 2 1/4 2 Door 5/16 - |- 12 GA, MIN
REINFORCEMENT
FOR METAL DOORS
590 MOUNTING GROUP BUTT WIDTH 13.19 0 1014 vo|∞ 21 - 28 + 1 A
SWING CLEAR HINGE 		|
| 		REINFO
FOR ME 		_
590 MOI HINGE TYPE OFFSET PIVOT SWING CLEAR
HINGE 		OFFSET - J+ V
1 ပ 17 7 91 21 30R STOP
ů В 3 3 6 8 10 3 BOTTOM OF DOOR STOP +
STOP) 110 A ء
ائ 		- l 4 7 5 8 B0T1 تــــ
DEGREE OF OPENING AT HOLD OPEN (SEE NOTE 2 FOR STOP) 105° В ا ۍ - 1 7 1 8 11 1 8 [
NOTE 1 A 2 7 6 3 ω
N (SEE 100 В 4 . | 7 1/2 11 2 7
LD OPE _ A ď 6 8 8 2 7/16 →
(ВОТН ENDS) 		+
AT HO 95° В -1 4 ω 12 (80 Г
PENING 0, A ا ع 7 6 - C - 8 RACKET
DGE OF
E OF OI .06 ш ال - 1 8
8|3 		12 5 /8 DOOR \| MOUNT JAMB BRACKET
FLUSH WITH EDGE OF
STOP 		ZWS
DEGRE L A ر
ا ک 		2 7 4 6
- | 4 		MOUN. - 1/4-20 X 1/2
MACHINE SCREWS
OR #14 X 1 1/2
WOOD SCREWS 		REQUIRE
85° В 7 7 - 8 2 131 - B 7 3 ************************************** /
YAA
143±008 		3
¥ - 1 ω, 80
←14 		10 1/8 1 FOR BUTT HING H \frac{1}{2}
ACTUAL
DOOR WIDTH 		322 -39 1 AND ų
| 		+ 9.08 7
1 + 7 32 $ 39 1 NGE 7 _
MODEL
NO. 		597H
& 		5975 598Н
&
598S 		599Н
&
599S 		¢ HINGE ſ 7 1

FECTIVE DATE APRIL 02 темпляте ю. А7479 В - DRILL Ø 7 HOLE FOR GROMMET NUT SARGENT Manufacturing Company 100 Sargent Drive New Haven, CT 06511 DATA SHEET: 597-599 SERIES DOOR HOLDERS AND STOPS - MOINTING GROUP 1 DRILL # 5 HOLE FOR 5/16-18 x 2 3 13/16 THRU-BOLT SUFACE MOUNTED ___ JAMB BRACKET CHANNEL JAMB BRACKET DETAIL ٦ ۲ 13/16

'A' & 'B' DIMENSIONS ARE GIVEN FROM € OF HINGE. ۵.

1. DIMENSIONS ARE GIVEN FOR THE HOLD OPEN POSITION. DEAD STOP OCCURS 5.-9. AFTER HOLD OPEN.

FOR DEAD STOP TEMPLATING, ADD 1/2 TO DIM. 'A' AND 3/8 TO DIM. 'B'.

  • 4. LEFT HAND SHOWN, RIGHT HAND OPPOSITE.
  • THRU BOLTS AND GROMMET NUTS PROVIDED ALLOWS CHANNEL TO BE MOUNTED ON 1 3.74\, 2\, DOORS. 5.

3/16

  • FOR DOORS UNDER 25. WIDE, THE STOP MAY HAVE TO BE MODIFIED TO ALLOW FOR CHANNEL CLEARANCE. 9
  • FOR CONTINUOUS HINGES USE SIMILAR BUTT HINGE VALUES. 7

Copyright © 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.

A7499A

ASSA ABLOY

Copyright © 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.