INSTALLATION INSTRUCTIONS FOR F SERIES LOCKS

MARK DOOR

Recommended template instructions must be followed to assure prroper functioning. (See attached template). Mark height line on edge of door 38" from floor.

Using height line, mark centers for latch hole and side hole on both sides of door.

2

1 BORE 3 HOLES

A. Bore side hole from both sides of door.

B. Bore latch hole. Use strike locating tool or other pointed object to locate position for hole in frame.

A

C

B

C. Bore frame.

NOTE: A minimum 3/4" deep hole must be bored in frame behind opening in strike for proper function of latch bolt.

Outline latch face and strike as illustrated and chisel out to proper depth.

INSTALL LATCH AND STRIKE

Be sure beveled side of latch bolt is facing the door frame.

clear area with wood chisel.

4

REMOVE INSIDE TRIM

Depress locking button to remove knob or lever. *

Pull knob or lever off of spindle. Unsnap rose from mounting plate. It will be necessary to pry the rose with a very thin flat screwdriver, nail or other thin object. Pry under or near the tiny depressions on the edge of the rose and remove from spindle.

RECOMMENDED TEMPLATE INSTRUCTIONS MUST BE FOLLOWED TO ASSURE PROPER FUNCTION.

Remove template from instructions

* If cylinder knob or lever, see below.

INSTALL OUTSIDE KNOB OR LEVER

IMPORTANT NOTE:

When opening outer trim by key, always mount through latch hub to avoid misalignment.

INSTALL INSIDE ASSEMBLY

Slide inside assembly over locking bar; insert and evenly tighten machine screws. Note: Locking button in lever locks must be positioned towards the edge of the door.

INSTALL ROSE AND KNOB OR LEVER

Check lock function to verify satisfactory operation. Snap rose over mounting plate. Place knob or lever on spindle, slide to locking button, depress button and push knob or lever until button engages hole.

INSTRUCTIONS FOR KNOBS WITH CYLINDERS

CYLINDER KNOB SHOULD BE INSTALLED WITH KEY NOTCHES UP AS SHOWN

© Allegion 2014 Printed in U.S.A. 030091-000-70 Rev. 10/14-d

INSTRUCTIONS FOR REMOVAL AND REASSEMBLY OF CYLINDER KNOB

With key, unlock lockset. Retract key halfway from cylinder. Depress locking button and pull off knob with cylinder. Rotate cylinder 180° and slip knob back onto spindle.

TO INSTALL CYLINDER KNOB

With key in cylinder, align hole in knob and cap and slip knob over spindle up to locking button.

STEP ONE STEP TWO

With knob or lever aginst locking button, depress locking button and push knob or lever until button engages hole. Test for proper operation.

DISTANCE FROM EDGE (BACKSET) OF DOOR for 1 Center ³⁄₈" (35mm) Doors for 1 Center ³⁄₄" (44mm) Doors 15/16" (24mm) PARALLEL TO SIDES. BORE LATCH HOLE FOLD ALONG EDGE OF DOOR

BORE 2 FIRST

Height Line

2³⁄₄" (70mm)

2³⁄₈" (60mm)

¹⁄₈

" (54mm) HOLE AT CORRECT BACKSET

TEMPLATE

SECOND

Additional Notes:
1. None

		Revision	History			Revision Description:
А	В	С	D	E	F	D > Revised artwork
none	0790	6683
Material	Material White Paper					Edited By	Approved By	EC Number	Release Date
						J. Ellis	M. Roberts	xxxxx	10/14
Notes	Notes					Title
	printed one side printed black					Falcon F Series Locks
	3. tolerance ± .13					Creation Date	Number	mber
4. printed	4. printed in country may vary					10-22-14	030091-000-70		D
						Created By J. Ellis	Activity 3899 Hancock Expwy
						Software: InDesign CS6	Security, CO 80911		© Allegion 2014