EPlex 2000 Door Preparation Drawing Sargent 8710F (IP-513914 v2)
Open the original PDF document
View PDF3 RÉVISIONS NOTES: 1- FOR EXIT DEVICE AND MORTISE LOCK CUT-OUT REFER TO EXIT DEVICE MANUFACTURER INSTALLATION INSTRUCTIONS. REV ECN DESCRIPTION VÉRIFIER PAR DATE 14013 ORIGINAL RELEASED FOR PILOT IPT Α.Τ. 5DEC2011 2- BACKSET SHOWN FOR REFERENCE ONLY, ADJUST BACKSET TO EXIT DEVICE MANUFACTURER INSTALLATION INSTRUCTIONS. 15719 NOTES ADJUSTED, NEW DESCRIPTION, DWG REDONE ON SW A.E. C.D. 21JA2016 BACKSET TO BE ADJUSTED TO LOW AND HIGH BEVEL DOOR EDGE AS PER DIAGRAM A TABLE. 3- DIMENSIONS ARE SYMETRICAL ABOUT © UNLESS OTHERWISE NOTED. 4- THIS HOLE ONLY FOR LOCK WITH MESSENGER OR BLUETOOTH. FOR COMPLETE HOLE PATTERN REFER TO DRAWING DT-515150/IP-515150 FOR SURFACE MOUNT VERTICAL RODS. D 5- ALL DIMS ARE IN INCHES/[mm] DOOR TOP SPECIFIC TOLERANCES 19.05 DISTANCES ±.030 [0.75] Ø.750 HOLES ∅ SEE NOTE #4 ±.010 [0.25] +.030 [0.75] DIMS MARKED # 4X Ø .313 7.94 ] -.000 [0.00] 57.15 2.250 34- BACK SET SEE NOTE #2 [130.18] [ 131.75 ] 5.187 5.125 186.84 RIGHT LEFT HIGH BEVEL HAND HAND 7.356 25.40 LOW BEVE LOW BEVEL 1.000 € LOCK LEVER 38.10 LOW BEVEL LOW BEVEL RIGHT LEFT 53.98 1.500 HAND HAND HIGH BEVEL 2.125 REVERSE REVERSE -(±)- <del>-(---</del>-38.86 LHR LOCK 1.530 DOOR DOOR INSIDE DOOR OUTSIDE BOTTOM (EXIT DEVICE SIDE) DIAGRAM A - BACK SET AJUSTEMENT FOR 3° BEVEL DOOR LE MATÉRIAU ET LA FINITION DE CETTE PIÈCE DOIVENT RESPECTER LES DIRECTIVES ENVIRONNEMENTALES; RÉFÉRENCE AUX STANDARD D'INGÉNIERIE DE KABA ES-073. MATERIAL AND FINISH OF THIS PART TO COMPLY WITH ENVIRONMENTAL DIRECTIVES; REFERENCE TO KABA'S ENGINEERING STANDARD ES-073. BACK SET SCALE 1:2 BEVEL EDGE DOOR THICKNESS AJUSTEMENT DIMENSIONS CRITIQUES DIMENSION X SANS AUTRES SPECIFICATIONS, 7301, Décarie Boul. DIMENSION XXX A.EL QUAFI 2011-07-14 LES DIMENSIONS SONT EN POUCES ET S'APPLIQUENT APRÈS FINITIONS. CRITICAL DIMENSIONS Montréal, Qc, Canada PROJECTION 3 iemes ANGLE H4P 2G7 31,8mm 0.81mm 2011-07-14 A.EL OUAFI THIRD ANGLE PROJECTION www.kaba-ilco.com LINI ESS OTHERWISE SPECIFIED TANDARD 38,1mm 1,00mm NE PAS MESURER SUR LE DESSIN DIMENSIONS ARE IN INCHES 2011-07-14 TITRE BACK-SET DO NOT SCALE DRAWING DIMENSIONS AND TOLERANCING AS PER AMERICAN SOCIETY OF MECH ENGINEERING AND APPLY AFTER FINISH. 44,5mm 1.17mm AND POWER-PLEX 2000 LOCK SERIES TOLERANCES DOOR PREPARATION DRAWING SAUF SI SPECIFIÉES AUTREMENT UNLESS OTHERWISE SPECIFIED. APPROVED BY: 50,8mm 1,32mm ASME T14.5-1994 FOR SARGENT SURFACE ROD 12-43-NB-8710-FXETL 32D 1,50mm 57,2mm FRACTIONS ±1/64" N/A DECIMALES - DECIMALS 63,5mm 1,65mm .X ± .03 N/A IP-513914 HIGH BEVEL EDGE N/A 69,9mm 1,83mm .XX ± .02 В ÉCHELLE: SEE VIEWS METRIC .XXX ± .010 SCALE: 1:4 (±) UNE VERSION FRANÇAISE DE CE DOCUMENT EST DISPONIBLE SUR DEMANDE. 1 of 2 .XXXX± N/A N/A
