EPlex 2000 Door Preparation Drawing Arrow Rim S3888, Arrow Surface Rod S3788 (IP-513127 v4)

REVISIONS NOTES: ECN DESCRIPTION DATE 1- FOR EXIT DEVICE AND MORTISE LOCK CUT-OUT REFER TO EXIT DEVICE MANUFACTURER INSTALLATION INSTRUCTIONS. 2- BACKSET SHOWN FOR REFERENCE ONLY, ADJUST BACKSET TO EXIT DEVICE MANUFACTURER INSTALLATION INSTRUCTIONS. 12AU ORIGINAL RELEASED FOR PILOT P.P. 1 13259 A.T. BACKSET TO BE ADJUSTED TO LOW AND HIGH BEVEL DOOR EDGE AS PER DIAGRAM A TABLE. 2009 3- DIMENSIONS ARE SYMETRICAL ABOUT $\( \text{ UNLESS OTHERWISE NOTED.} \) 20JA 2 15719 NOTES ADJUSTED, NEW DESCRIPTION C.D. A.E. 2016 4- THIS HOLE ONLY FOR LOCK WITH MESSENGER OR BLUETOOTH. FOR COMPLETE HOLE PATTERN REFER TO DRAWING DT-515149 OR IP-515149 FOR RIM AND MORTISE LOCKS OR DT-515150/IP-515150 FOR SURFACE MOUNT LOCKS. DOOR 5- ALL DIMS ARE IN INCHES/[mm] SPECIFIC TOLERANCES TOP DISTANCES ±.030 [±0.75] BACK SET $\backslash emptyset$ .750 HOLES ∅ ±.010 [±0.25] SEE NOTE #2 [19,05] SEE NOTE #4 2.250 [57,15] $\backslash emptyset$ .313 [7,95] √ .75 [19,05] LEFT HAND RIGHT HAND (LH) (RH) INSIDE 1.500 [38,1] OUTSIDE 5.125 4.922 LEFT HAND RIGHT HAND [130,18] REVERSE REVERSE [125,02] (LHR) (RHR) RAM B HANDING DIAGRAM B 7.356 [186,84] $\backslash emptyset$ 1.000 [25,4] ↓ LOCK LEVER 1.766 2.125 [44,85] [53,98] Ø .500 [12,7]

LHR LOCK DOOR DOOR DOOR INSIDE OUTSIDE BOTTOM (EXIT DEVICE SIDE)

UNE VERSION FRANCAISE DE CE DOCUMEN

DIAGRAM A - BACK SET AJUSTEMENT FOR 3 BEVEL DOOR BACK SET -LOW BEVEL EDGE OOR THICKNESS AJUSTEMENT DIMENSION X DIMENSION Y .032 (0.81mm) 1.25 (31,8mm) 2.750 STANDARD 1.50 (38,1mm) .039 (1,00mm) BACK-SET 1.75 (44,5mm) .046 (1.17mm) 2.00 (50,8mm) .052 (1,32mm) 2.25 (57,2mm) .059 (1,50mm) REFERENC 2.50 (63,5mm) .065 (1,65mm) HIGH BEVEL EDGE-2.75 (69,9mm) .072 (1,83mm)

SYMBOLS: $\backslash sqrt\{\backslash phantom\{a\}\}$ DEEP ___ COUNTERBORE CENTER LINE $\backslash emptyset$ DIAMETER ✓NOT TO SCALE

SCALE 1:2

XXX	DIMENSIONS CRITIQUES CRITICAL DIMENSIONS	SANS AUTRES SPECIFICATIONS, LES DIMENSIONS SONT:POUCES [millimètres]
$$\backslash oplus\; \backslash circlearrowleft$$	PROJECTION 3iem ANGLE THIRD ANGLE PROJECTION	ET S'APPLIQUENT APRÈS FINITION.
		UNLESS OTHERWISE SPECIFIED,
NE PAS MESURER SUR LE DESSIN		DIMENSIONS ARE:INCHES [millimeters]
DO	NOT SCALE DRAWING	AND APPLY AFTER FINISH.
	G AND TOLERANCING AS PER OCIETY OF MECH ENGINEERS 994	TOLERANCES:
CE DOCUMENT EST LA PROPRIETE STRICTE DE KABA. LES DONNEES QU'IL, CONTIENT NE PEUVENT ETRE COPIEES DU DIVUL GUESE À UNE TIERCE PARTIE SANS LE CONSENTEMENT ECRIT DE KABA. CE DOCUMENT		THIS DRAWING HAS SPECIFIC TOLERANCES,

HIS DOCUMENT IS PROPERTY OF KABA. THE DATA ONTAINED IS PROPRIETARY AND SHALL NOT BE CE DESSIN A DES TOLERANCES SPECIFIQUES, VOIR LES NOTES

DESSINE PAR DRAWN BY: P.PRIEUR 12AU09 CONCU PAR: DESIGNED BY A.TOLEDANO 12AU09 PROLIVE PA PPROVED BY MATERIAU / MATERIAI NOT APPLICABLE

630, 730, 750, 79E, E-PLEX 2000 AND POWER-PLEX 2000 LOCK SERIES

DOOR PREPARATION DRAWING ARROW RIM S3888, ARROW SURFACE ROD S3788 FINITION / FINISH ORMAT NO PIECE / PART NO NOT APPLICABLE N/A IP-513127 В TRAITEMENT THERMIQUE / HEAT TREATMENT DE OF SEE VIEWS NOT APPLICABLE

7301.Decarie Boul

Montreal,QC Canada H4P 2G7

SEE PAGE 1

JERSION A

RHR LOCK

CE DOCUMENT EST LA PROPRIETE STRICTE DE KABA. LES DONNEES QU'IL CONTIENT NE PEUVENT ETRE COPIEES OU DIVULIQUEES A UNE TIERCE PARTIE SEN LE CONSENTMENT ECRIT DE KABA CE DOCUMENT DEVRA ETRE RETOURNE SUR DEMANDE A KABA.

THIS DOCUMENT IS PROPERTY OF KABA. THE DATA CONTAINED IS PROPRIETARY AND SHALL NOT BE COPIED OR DISCLOSED TO A THIRD PARTY WITHOUT WRITTEN CONSENT OF KABA. THIS DOCUMENT WILL BE RETURNED TO KABA UPON DEMAND.

UNE VERSION FRANCAISE DE CE DOCUMEN EST DISPONIBLE SUR DEMANDE.

8		KARA	Mor H4F	7301,Decarie Boul Montreal,QC Canada H4P 2G7 www.kaba-ilco.com
	FORMAT	NO PIECE / PART NO:	/ PART NO: NO DESSIN / DRAWING NO:
E	R	N/A	I	P-51	513127
NT	ט ן	FOR COMPLETE TITLE REFER TO PAGE 1	PG SHT	2	DE OF	2