Corbin Russwin ML2000 Series Mortise Locks Master Ring Cylinder (MR) Template_T30605
Open the original PDF document
View PDFNotes: Required Holes Required Holes A B C D E CYL O/S Function В Function Backset is measured from centerline of ML 2056 bevel which is centerpoint of door B =CYL BOTH SIDES ML 2002 Х Χ Х Χ Χ Χ thickness. C =TP I/S ML 2003 Χ Χ Х ML 2057 Χ Χ Χ 2. (*) When preparing doors for lead wrapped D = LEV HOLE ML 2004 Χ Χ Χ Х ML 2058 Χ Χ Χ Х locks, add 1/8 (3.2) to dimensions marked E =THRU-BOLT HOLE's ML 2011 Χ ML 2059 Χ Χ Χ (*) to allow proper clearance. ML 2012 ML 2062 Χ Χ 3. 1-1/8 (28.6) strike lip suits frame for 1-3/4 (44.5) thick door, lip will vary for other ML 2013 Χ G =Front Pocket Width Χ ML 2065 Χ Χ Χ Χ door thicknesses. ML 2022 Х Χ ML 2067 Χ Χ Χ Χ Х H =Front Pocket Halt Width For preparation of trim, refer to separate Mortise Pocket Width ML 2024 Χ Χ Χ Х ML 2068 Χ Χ Χ Χ template. ML 2042 Χ Χ Х ML 2069 Х Χ Χ Χ 5. For open back strike, refer to template ML 2048 Х Χ Χ Х ML 2072 Χ Χ Χ T30606. Dimensions given in inches and (mm). ML2049 Χ Χ Χ Х ML 2073 Χ Χ Χ ML 2051 Χ Χ Х Χ ML 2075 Χ Χ ML 2052 Χ Χ Х ML 2082 Χ Χ Х ML 2053 Χ Χ Χ Χ ML2087 Χ Χ Χ ML 2054 Χ Χ Χ Χ ML 2092 Χ Χ Χ CAUTION: DOOR & FRAME MANUFACTURERS ML 2055 Χ Χ When door gasketing or silencers are used, proper allowances must be made for strike location to maintain a common centerline with lock and door as shown so that bolt will freely enter strike. Line "Y-Y" corresponds to Plaster Guard by Frame Manufacturer "Y-Y" on Trim Templates (31.8)1" Min. Min. (2.4) (25.4) *4-1/2 (114)(See Note 3) 2-3/4 Backset Frame (28.6)Master Ring Cylinder (70)Metal Door Wood Door (See Note 1) -5/8 (41.3) Dia. – Outside Only В 1-5/8 (41.3) Dia. Thru Strike/Lock/Door #12-24 Tap for Bevel #12-24 Tap Lock/Door Combination Screw 1/8 in 2" Turnpiece (2 Places) 1-1/4-.000 (2 Places) Door (3.2)(50.8)C 5/8 (15.9) Dia. – Inside Only .173 Dia. (31.8) Thickness Pilot Hole 7/32 5/8 (2 Places) (15.9) <u>3/4 Max.</u> (5.6)4-1/8 1-3/16 (104.8)(19.1) (30.2)(203.2)(203.2)-7/16 7-1/4 Cylinder 4-7/8 3-1/2 (61.9) 7-1/4 5-<u>5/8</u> (38.1)(184.2)(5.6)(142.9)િ Strlike (123.8) (88.9)(85.7) (92.1)Min. 6-Lock ' (9.5) 33.3) (168)Knob/ Knob/ (19.1)Lever Latch 1-1/2 Bolt Knob or Lever (38.1)2-1/8 2-1/8 2-1/2 D 7/8 (22.2) Dia. Thru 2-1/2 (54)1-13/16 Knob or Lever H→ 3/8 (9.5) Dia. Thru Ε G→ (2 Places) Door Detail FRAME DETAIL ANSI Strike Description 236L72 Latch & Dead Bolt Holes Door Thickness Tolerances 236L73 Latch Bolt Hole Only 1-1/4 (31.8) 5/8 (15.9) 1-1/16 (27) 1-3/4 (44.5) or Over (STD) Inches (mm) 236L74 Dead Bolt Hole Only 1-1/16 (27) | 17/32 (13.5) | 1-1/32 (26.2) 1-3/8 (34.9) (D138) .005 .127) And Optional Box 120F76 (.381 Corbin 7 RESPONSIBILITY ML2000 DOOR AND FRAME MANUFACTURERS ARE RESPONSIBLE FOR PROVIDING ADEQUATE Series by MR CONSTRUCTION OR REINFORCEMENTS FOR assa abloy PROPER INSTALLATION OF HARDWARE SHOWN.
ALL ARCHITECTURAL BUILDERS HARDWARE MUST BE INSTALLED ON PROPERLY REINFORCED DOORS AND FRAMES, REGARDLESS OF TYPE, MATERIAL, OR METHOD OF CONSTRUCTION.
Mortise Lock by Master Ring Cylinder
www.corbinrusswin.com
SUPERSEDES DO NOT SCALE DRAWING T30605-6 03/23
1 of
T30605-7
Experience a safer and more open world