Corbin Russwin Inspire Roseless Trim for ML20600 (NAC) and ML20900 Series Electrically Operated Mortise Locks Te…_T31251
Required Holes Notes: Series
Functions
С 1. Backset is measured from centerline of bevel which is ML20906 centerpoint of door thickness. Non-beveled door shown. ML20914 2. (*) When preparing doors for lead wrapped locks, add 1/8 (3.2) to dimensions marked (*) to allow proper clearance. ML20907 ML20915 3. 1-1/8 (28.6) strike lip suits frame for 1-3/4 (44.5) thick door, lip will vary for other door thicknesses. ML20932 4. For open back strike, refer to template T30606. ML20987 5. Dimensions given in inches and (mm). 6. Door fabricator to provide a Ø3/8 (9.5) minimum raceway through door to allow the insertion of electrical wires running between lock ML20606-NAC mortise and electric hinge. ML20607-NAC ML20608-NAC
CAUTION: DOOR & FRAME MANUFACTURERS
When door gasketing or silencers are used, proper ML20609-NAC allowances must be made for strike location to maintain a common centerline with lock and door as shown so that bolt will freely enter strike. Plaster Guard by Frame Manufacturer 1-1/4 Cylinder (31.8)A 1-5/16 (33.3) Dia. – Outside Only 1" Min. Min. (2.4)(25.4) B 1-5/16 (33.3) Dia. Thru Turnpiece - Inside
Metal Door Prep Wood Door Prep
5/8 (15.9) Dia. - Inside Only 1 - 1/8(See Note 3) Frame (28.6)Wire Raceway #12-24 TAP .173 Dia. LStrike/Lock/Door (See Note 6) #12-24 Tap for 1.25 (31.8) Pilot Hole Combination Screw Min. Depth (2 Places) 1-1/4-000 1-3/16 (2 Places) (2 Places) 1.250 -.000 + 0.31(114.3)(30.2)(31.8)3/8 5/8 Ø3/4 (31.8)Ø1.125 -.000 (9.5)(19) (15.9) 3/4 <u>Max</u> 4-1/8 R .125 (3.2) (28.6)(104.8)Max. (19.1)(4 Places) +.03-.000 Cylinder 2-7/16 6-5/8 nз + 015 (61.9)-.000 + 031 (168)3-3/8-005
GStrike
8" 4-7/8 3-1/2 5.625 - .000 (27)(203.2)(142.9)1.000 +.031
(88.9) (85.7) – 3-5/8 <u>1.125</u> Min. Lock Min. 3/8 (92.1)(25.4)(28.6)7-1/4 (9.5)(184.2)€Knob/ 7.250 1-1/2 11/16 500 ±.031 (184.2)Lever (38.1)1.000 -.000 (17.5) (63.5)(25.4)Min. +.031 (12.7)1.250 -.000 3/8 1.188 ±.008 375 9/16 219 (9.5)(30.2)(31.8) (95.3)(14.3)(5.6) (64.3)2.750 ±.031 (69.9)
Tolerances
Inches (mm) (.127).005 .010 (.381) .015 RESPONSIBILITY DOOR AND FRAME MANUFACTURERS ARE RESPONSIBLE FOR PROVIDING ADEQUATE ML20900 & ML20600-NAC Series CONSTRUCTION OR REINFORCEMENTS FOR assa abloy PROPER INSTALL ATION OF HARDWARE SHOWN Inspire™ Roseless Trim www.corbinrusswin.com ALL ARCHITECTURAL BUILDERS HARDWARE MUST SUPERSEDES BE INSTALLED ON PROPERLY REINFORCED DO NOT SCALE DRAWING DOORS AND FRAMES, REGARDLESS OF TYPE. TEMPLATE NUMBER T31251 05-19 MATERIAL, OR METHOD OF CONSTRUCTION.